The "WizardProg Mobile" (professional version application is "WizardProg Expert") application software designed to manage the programming operation for the universal portable USB-programmer TL866A/CS and other programmer models which fully compatible with it. This system is used to program a wide range of E(E)PROM chips, microcontrollers internal EEPROM, testing SRAM chips and logic chips.
The application allows you to achieve a new level of mobility and efficiency when using the programmer TL866, which is used widely to repair and adjustment:
· automotive computers, computer-unit and radio;
· personal computers;
· any other modern electronic equipment.
The "WizardProg Mobile" system is used by service technicians of electronics, amateur radio operators and developers of modern electronic devices for the purpose of:
· repair and restore the microelectronic device and firmware;
· promptly update the firmware of microelectronic devices;
· assist in the embedded electronics construction and setting up the microcontroller units;
· replicate numerous useful designs using advanced electronic components.
Main characteristics and features of the "WizardProg Mobile" microelectronic programming system are:
· Fast and reliable programming, in most cases with significantly better speed than the similar systems.
· The programmer's low power consumption when powered by USB (OTG)-cable from the mobile device battery.
· Support for a wide range of integrated circuits (ICs): the memory of a large capacity up to 128Mbit (EPROM, FLASH, EEPROM I2C/3-wire/SPI), microcontrollers PIC, Atmel-AVR, MCS-51 based SST, SyncMOS, Winbond. PLD chips, GAL.
TL866 programmer does not need an external power supply and it operates using the power sources of a tablet or mobile phone which is connected to via USB interface. Physical linking to a mobile device is provided with a USB cable fully supporting OTG (On-The-Go) protocol.
Important note! The target control tablet or mobile phone must have a fully implemented hardware support of OTG access too!
Currently "WizardProg Mobile" mobile application is completely autonomous in operation, does not need a permanent connection to the Internet, allowing you to use it even without access to communication networks.
Both of programmer's models TL866CS and TL866A(ICSP) are fully supported. The modern version of the TL866II Plus programmer currently is not supported by the "WizardProg Mobile" system!
Device list for the current application version: http://www.wizardprog.com/wp/dblist/recent_version_chiplist.htm
แอพพลิเคชั่น "WizardProg Mobile" (รุ่นมืออาชีพคือ "WizardProg Expert") ซอฟต์แวร์แอพพลิเคชั่นที่ออกแบบมาเพื่อจัดการการทำงานของการเขียนโปรแกรมสำหรับโปรแกรมเมอร์ USB พกพาอเนกประสงค์ TL866A / CS และรุ่นโปรแกรมเมอร์อื่น ๆ ที่เข้ากันได้อย่างสมบูรณ์ ระบบนี้ใช้เพื่อตั้งโปรแกรมชิป E (E) PROM หลากหลาย EEPROM ภายในไมโครคอนโทรลเลอร์การทดสอบชิป SRAM และชิปตรรกะ
แอปพลิเคชั่นช่วยให้คุณได้รับความคล่องตัวและประสิทธิภาพในระดับใหม่เมื่อใช้โปรแกรมเมอร์ TL866 ซึ่งใช้กันอย่างแพร่หลายในการซ่อมแซมและปรับแต่ง:
·คอมพิวเตอร์ยานยนต์คอมพิวเตอร์และวิทยุ
·คอมพิวเตอร์ส่วนบุคคล
อุปกรณ์อิเล็กทรอนิกส์สมัยใหม่อื่น ๆ
ระบบ "WizardProg Mobile" ถูกใช้โดยช่างบริการด้านอิเล็กทรอนิกส์ผู้ประกอบการวิทยุสมัครเล่นและผู้พัฒนาอุปกรณ์อิเล็กทรอนิกส์ที่ทันสมัยเพื่อวัตถุประสงค์ในการ:
ซ่อมแซมและกู้คืนอุปกรณ์ไมโครอิเล็กทรอนิกส์และเฟิร์มแวร์
·อัปเดตเฟิร์มแวร์ของอุปกรณ์ไมโครอิเล็กทรอนิกส์ทันที
·ช่วยในการสร้างอุปกรณ์อิเล็กทรอนิกส์ฝังตัวและติดตั้งหน่วยไมโครคอนโทรลเลอร์
·จำลองการออกแบบที่มีประโยชน์มากมายโดยใช้ส่วนประกอบอิเล็กทรอนิกส์ขั้นสูง
คุณสมบัติหลักและคุณสมบัติของระบบการเขียนโปรแกรมไมโครอิเล็กทรอนิกส์ "WizardProg Mobile" คือ:
·การเขียนโปรแกรมที่รวดเร็วและเชื่อถือได้ในกรณีส่วนใหญ่ด้วยความเร็วที่ดีกว่าระบบที่คล้ายกัน
·การใช้พลังงานต่ำของโปรแกรมเมอร์เมื่อใช้พลังงานจากสาย USB (OTG) จากแบตเตอรี่โทรศัพท์มือถือ
·รองรับวงจรรวม (IC) ที่หลากหลาย: หน่วยความจำความจุสูงถึง 128Mbit (EPROM, FLASH, EEPROM I2C / 3-wire / SPI) ไมโครคอนโทรลเลอร์ PIC, Atmel-AVR, MCS-51 ที่ใช้ SST, SyncMOS, Winbond ชิป PLD, GAL
โปรแกรมเมอร์ TL866 ไม่ต้องการแหล่งจ่ายไฟภายนอกและทำงานโดยใช้แหล่งพลังงานของแท็บเล็ตหรือโทรศัพท์มือถือที่เชื่อมต่อผ่านทางอินเตอร์เฟส USB การเชื่อมโยงทางกายภาพไปยังอุปกรณ์มือถือนั้นมาพร้อมกับสาย USB ที่รองรับโปรโตคอล OTG (On-The-Go) อย่างเต็มที่
โน๊ตสำคัญ! แท็บเล็ตควบคุมเป้าหมายหรือโทรศัพท์มือถือจะต้องมีการสนับสนุนฮาร์ดแวร์อย่างเต็มที่ในการเข้าถึง OTG ด้วยเช่นกัน!
ขณะนี้แอปพลิเคชั่นมือถือ "WizardProg Mobile" นั้นทำงานโดยอัตโนมัติไม่จำเป็นต้องเชื่อมต่อกับอินเทอร์เน็ตอย่างถาวรช่วยให้คุณสามารถใช้งานได้โดยไม่ต้องเข้าถึงเครือข่ายการสื่อสาร
ทั้งสองรุ่นโปรแกรมเมอร์ TL866CS และ TL866A (ICSP) ได้รับการสนับสนุนอย่างเต็มที่ เวอร์ชันปัจจุบันของโปรแกรมเมอร์ TL866II Plus ไม่รองรับในระบบ "WizardProg Mobile"!
รายการอุปกรณ์สำหรับเวอร์ชันแอปพลิเคชันปัจจุบัน: http://www.wizardprog.com/wp/dblist/recent_version_chiplist.htm